Utilizing a high vacuum chamber, the test system is used to test pre-charged parts for leaks which are too small to be detected via vacuum or pressure decay tests. It replaces the subjective bubble leak test while eliminating hours of required test time. Typical configuration consists of pressurized air supply for high vacuum chamber door operation along with a 460/3/60 power supply to minimize system current draw. Once the chamber door is closed, the roughing pump evacuates the chamber in preparation for the ultra-fine leak test. After part leak test is complete, the chamber is vented, the part may be removed and the system resets for the next test.

The post Burst Test/Helium Mass Spectrometer Leak Test System appeared first on PCU.

The rotary index table is setup so that the early stations are utilized for component assembly and the latter stations utilize various testing technologies to verify the assembly’s integrity and may perform a final fluid fill. Each station is designed for independent operation and is able to be individually configured.

Typical configuration consist of a pressurized air supply for articulation and operation along with a 460/3/60 power supply to minimize system current draw. The component assembly stations are fed with bowl feeders and configured with a pick and place arm. The assembly is then fed into an integral mass spectrometer for ultra fine leak testing. The mass spectrometer utilizes a high vacuum chamber to facilitate the automated leak test. After part leak test is complete, the helium is removed from the part and the part is prepared for final fluid fill. The final stages are used to check the completed assembly with vision systems and run testing. Finally, the part may be removed from the index table manually or with an automated articulating assembly.

The post Rotary Index Table appeared first on PCU.

• • Two-stage rotary vane roughing pump
  • Integrated Inficon LDS 2000 mass spectrometer
  • Onboard NIST traceable calibration verification capable
  • Integral test verification with every cycle
  • Multiple fault indicators
  • Allen-Bradley Panel View Micro 300 Operator Interface Terminal 700
  • Data mining w/printer capable
  • Optional power requirements available
  • Optional chamber configurations available
  • Capable of detecting leaks to 1×10-9 atm cc/sec*
  • Total test time less then 40 seconds ( Test is dependent on part configuration)

The post Helium Mass Spectrometer Leak Test Chamber appeared first on PCU.

• • Economical
  • Various styles/sizes of systems
  • PLC controlled
  • Fully automatic process
  • Adjustable parameters
  • Customizable process and cycle options
  • Fault indicators
  • Remote monitoring
  • Compressor monitoring
  • Barcode reader product identification
  • Data mining w/ printer
  • Quick connect tooling
  • Various safety devices
  • Oil-less Compressors
  • Air or Water Cooled

The post Helium Mass Spectrometer Leak Test System appeared first on PCU.

The operator connects the PCU tube quick connect (TQC) couplers and process hoses then presses the start cycle pushbutton. The product is filled with the proof test gas. If the product fails to achieve the required proof test pressure the product is rejected (red light) and will not be filled with helium. After the product passes the proof test phase of the cycle the proof test gas is exhausted from the product into the atmosphere. The product is evacuated to remove air prior to the product being filled with the tracer gas. After the product is verified that it is at pressure the machine will indicate (yellow light) to the operator to begin manual sniffing. The operator manually sniffs all joints using a tracer gas leak detector. If a leak is detected a red light will illuminate. A green light will illuminate signaling an acceptable test. After all joints have been sniffed the operator depresses the tracer gas recovery pushbutton. The tracer gas will be recovered from the product by the plant wide tracer gas system; otherwise the tracer gas will be vented to atmosphere. The operator removes the process hoses and PCU TQC couplers. The operator finally installs the rubber plug, inserts the hypodermic needle into the rubber plug and fills the product with a low pressure shipping charge.

Features and Options

• • Fully automatic process

• • Operator Interface Terminal

• • Customizable process and cycle options

• • Multiple selection criteria

• • Continuous monitoring of parameters

• • Automatic clamp tooling

• • Rapid flow precision tooling

• • High-speed fill rates

• • Barcode reader product identification

• • Fault indicators

The post Proof Test and Tracer Gas Charge Stand appeared first on PCU.

•Two-stage rotary vane roughing pump with blower
•Integrated Inficon LDS 2000 mass spectrometer
•Onboard NIST traceable calibration verification capable
•Integral test verification with every cycle
•Multiple fault indicators
•Allen-Bradley Panel View
•Allen-Bradley Micro Logix 1500
•Data mining w/printer capable
•Optional power requirements available
•Optional chamber configurations available
•Capable of detecting leaks to 1×10-5 atm cc/sec*
•Total test time less then 2 minutes (Dependent on part configuration and test time)

The post Burst Test/Helium Mass Spectrometer Leak Test System appeared first on PCU.

The post Fuel Tank Tester appeared first on PCU.

• • Refrigerant Leak Testing
  • Tracer Gas Systems
  • Burst and Pressure Decay Leak Testing
  • Performance Testing
  • Capacity Testing
  • Durability Testing
  • Helium Mass Spectrometer
  • Completed Product Run Testing

Transportation Applications

• • A/C Leak Testing
  • Vehicle Brakes Testing
  • Fuel System Leak Testing
  • Radiator Systems Testing
  • Helium Mass Spectrometer
  • Completed Product Run Testing
  • Performance Testing
  • Capacity Testing
  • Durability Testing

Features and Options

• • Economical
  • Various styles/sizes of systems
  • PLC controlled
  • Fully automatic process
  • Operator Interface Panel
  • Allen Bradley PanelView®Touchscreen
  • Allen Bradley PanelView®Touchscreen
  • Adjustable parameters
  • Customizable process and cycle options
  • Fault indicators
  • Remote monitoring
  • Barcode reader product identification
  • Data mining w/ printer
  • Various safety devices

The post Performance Testing appeared first on PCU.

• 3 Liter Capacity
• Portable
• Translucent Viewing
• Reservoir
• Fill Port Matches Reservoir Port
• On Board Storge of Hoses

Options

• Fluid Return Kit – Returns fluid to storage tank by air pressure on tho of fluid and drain hose is attached to storage tank.
• Vacuum and Pressure Digital Readouts available.

The post Test Tanks appeared first on PCU.

The post A/C Leak Test appeared first on PCU.